skip to main content
Call Us Email Us

Self-Test Emergency Lighting

Self-test emergency lighting automatically performs tests on itself to ensure that it will function correctly in the event of a mains failure.

BS5266-1:2016 is the main standard for emergency lighting. It requires a short functional test of each emergency lighting fixture once a month and a full discharge test every year. Especially in larger buildings these tests can easily be overlooked, so BS5266 recommends the use of automatic test systems if the person responsible is not able to ensure that manual testing will be done.

There are two main types of automatic emergency lighting testing, self-test and addressable self-test. Note that when we refer to self-test and addressable self-test we are concerned with self-contained emergency light fittings (which each contain their own batteries), not emergency lighting that is connected to a central battery system.

SELF TEST – WHAT IT DOES

Self-contained emergency light fittings all contain their own batteries and are connected to an unswitched live supply. In the event of a power failure the emergency fitting detects that the unswitched live supply is no longer at mains potential and the fitting is from that moment powered from its batteries.

A self-test emergency fitting therefore must check that:

  • When the unswitched live supply is disconnected the fitting automatically switches from mains to battery operation
  • When running on battery power the LEDs illuminate as intended
  • The LEDs stay illuminated for the intended duration – usually 3 hours

In addition to these checks, BS5266 recommend that steps are taken during testing to ensure that not all fittings are tested at the same time as that would, temporarily, compromise the integrity of the emergency lighting provision. Therefore, a well-designed self-test emergency light fitting will be designed to operate as follows:

Step 1: Product is installed and is connected to mains power
Step 2: Under its own control the fitting charges its batteries for 24 hours
Step 3: The fitting carries out its own discharge test for 3 hours and then re-charges
Step 4: Anytime from 15-30 days later (the interval is randomly determined) the fitting undertake it own 30 second functional test
Step 5: 30 days later the 30 second functional test is repeated and repeated again after another 30 days till it has been done 11 times.
Step 6: On the 12th time the fitting conducts another full discharge test

On completion of a monthly or an annual test, indicator LEDs and an audible buzzer will signal the status of the fitting. The status signals from NVC Lighting’s self-test products are as follows, and other manufacturers’ status signals are similar.

Self-Test Fault Indication Table

SELF-TEST – HOW IT WORKS

Every self-test emergency module or fitting contains some electronics and software.

Software in the fitting includes a timing (but not a calendar) function so that tests are scheduled at the correct intervals.

Electronic sensing circuitry monitors the current flowing into the LEDs. If the current drops below a threshold level it is an indication that the LEDs are not functioning and this will cause the yellow indicator LED to flash. Similarly, sensing circuitry monitors the battery terminal voltage and current and causes the red indicator LED to flash it the values sensed are out of tolerance.

WHAT ARE THE BENEFITS OF SELF-TEST EMERGENCY LIGHTING?

There are three main benefits of having self-test emergency lighting:

  • Peace of mind
  • Lower costs
  • Increased safety

 Regular testing of emergency lighting is essential to avoid the risk of being in breach of the Regulatory Reform (Fire Safety) Order (2005). Breaching this statutory instrument brings the risk of fines and imprisonment. For details of the legal status of emergency lighting and emergency lighting testing, please read here

Manual testing is legal, but easily overlooked or carried out incorrectly. Therefore, the benefits of self-test emergency light fittings are:

  • Peace of mind. Assurance that the correct tests in accordance with BS5266 are being carried out, this month and every month
  • Lower costs. Manual testing must be carried out by a suitable qualified person and it cannot be carried out all at once - fittings must be tested at staggered intervals. It is therefore expensive. For the small additional acquisition cost of self-test emergency fittings, a long-lasting cost reduction can be built into a building’s running costs.
  • Increased safety for the building occupants. Installing a self-test emergency lighting system ensures that any system failings are identified as quickly as possible so they can be rectified soon.

We have self-test versions of all our emergency lighting products. This includes a self-test version of our popular plug-in emergency conversion kit. This enables any of our LED panels and LED downlights to be converted to emergency or self-test emergency. No special skill is required – they just plug in – so if you an installer it would be wise to keep a few of these kits to hand. You can use them on any project where our panels and downlight are being used.

For details of our emergency range, click here 

The alternative automatic testing system is called Addressable Self-test. For details, see here